Mechanical and Electrical

Fuel: Diesel
Servicing: Every 15,000km ( we think). Last done just before we left Uk. – i.e.  has only done 1,000km since then.
APK: similar to NZ warrant of fitness but more comprehensive. This was done in  May 2011  in Zierikzee and is now up to date again
Motor:   2.5l VW diesel. Cruises easily at 130km on the motorway.
Electrics: These may present a challenge and we had many sessions trying to sort them out as we were given no guidance on how the system worked and which bit did what. But being Kiwis and having a wee grasp of French we finally got there. Actually it was more a case of Geoff being persistent and fiddly and working it out.   The fridge operates off the personal/camper battery and can drain it quickly.
 Batteries : There are two battery systems. One drives the usual vehicle electrics, the other  drives the interior lights etc in the van and we call that the camper/personal battery. IN theory this  should be charged by the engine alternator as you drive,  but that did not always work. Hence we now have a battery charger as well and an electric test meter. .  There were times when the car battery was drained by the personal battery.
The camper/personal battery is stored under the bench seat in the van. As you move the seat back and forth to make the bed it is relatively easy to dislodge the connections on this battery and hence it does not recharge when driving the next day or does not recharge from an external source.
Camper battery under polystyrene cover
and battery charger and extension cord. 
Geoff's fingers are under a fuse which blew several times.
We didn't know why.



















Electric plugs- 220-240V. 


 I cannot remember if we left a NZ- Continental  adaptor in the van or not – I suspect not but it has  2 European plugs above the sink to plug into. The 240 V socket near the door connects to nothing. A remnant of the previous version of the van.


 --When you book in for a powered site you will often be asked how many amps you want access to point– the more amps, the more the cost.  We always chose the lowest because we didn’t have many electrical things.  If you try and draw more current than is available at your plug the circuit breaker at your camp supply will flick out and you may have to find the camp manager to reset it – particularly in France where the whole connection may be in a locked box so that you can’t leave without paying! 
------- To save you from this problem the van has an internal circuit breaker which clicks out if you draw more than whatever current you have set it to.  Each time you connect to a power site, this internal controller resets to a default of 2.0 amps (I think).    The LED figures on the “Fuse Control” box (below left) will show 2.0 in solid figures – as opposed to flashing figures.  Try and draw more and the fuse controller will click out and the figures will start flashing at you.  To reset the fuse controller you have to unplug the van from the power point and then reconnect.  To reset the amount the fuse controller will let you draw, press the “+” and “-“ buttons on the “Fuse Controller” at the same time.  The LEDs will start flashing.   Now press the “+” to increase the maximum current to that of the circuit breaker on your camp power point.  Leave it alone for a few seconds and it will go back to solid figures at the new max current.    Done that?  Congratulations.  You now have 240 volts connected to the van, and you have bright lights and your van battery is, in principle at least, recharging.  If it does not recharge, you can plug the battery charger in to the 240 v power outlet and recharge the battery manually.

:)  You are now the recipient of valuable knowledge gained at the expense of endless frustration and tinkering.  The switches and the power point below the “Fuse Control” budget don’t work or do anything – apparently they are the remnants of an earlier electrical system.  Play with them as much as you like!
Fuse control box. 
Switches - see note below






                                    














     
        The picture on the right shows the switches (one is broken – doesn’t currently seem to work anything, but if you ever manager to find a replacement rocker switch please put it in place.


 ·         The bottom left red rotary switch has to be turned to liven the 12 volt system.  The top switch in the bank of four has to be on for the lights to work.  The lights are also individually switched.  Second is broken; third works the cool box I think and the fourth may live the 12v plug just below the switches.


So if you want to use 240v to liven up your internal 12v lights there is a hell of a lot of things to get right. 
 1.  Connect to mains.  2. Reset the internal power supply controller.  3. Turn the rotary switch. 
 4. Turn on the top switch of the four.  5. Turn on your individual light switch.  
We concluded that the Europeans like to have complex systems!

Also included 
-- External plug with connector and adaptor means you can access power for all of Europe and the Uk       
-- Extension cord is under bench seat. We used it for the battery charger.
-- Battery charger: You may need it. Stored under the bench seat.
-- Volt meter
-  -Lighting- Some of lights run off camper battery but others will only run once you have connected to an external 240v source.
-- Hand powered torch

·       Tyres: a spare set of snow tires is available for use if you need them. These are compulsory In Switzerland in winter but leave them behind in Holland unless you need them.